1967 Kaiser M715

LS1/SM465/NP205, Twin Sticked, Custom Dana 60 Front/Dana 70 Rear, 4.56 gears w/ Detroit Locker, Four Wheel Disk 

• Paint

  • • PPG Pepper Gray - Code: 931611

    • PPG Cyber Gray - Code: 920131 

    • PPG Matt Clearcoat = Code D8115

• Engine

  • • Corvette 5.7 LS1 

    • Block Hugging Center Drop Headers.  

      • • NOTE: Required to clear manual clutch linkage and a ton of other stuff on driver side.  Long Tubes WILL NOT work.

    • Summit Racing Crossflow Radiator & Dual Spal Kit - Part#: SUM-3844012-KIT1

      • • 1,300-1399 cfm

    • Steam Vent Solution

      • • Fragola MPT Fitting - Part#: 484004-BL

          • Installed in top radiator hose

        • Mishimoto Water Temp Sensor Adaptor - Part#: MMWHS-28-BK 

    • LS1 Truck Oil Pan - Part#: WND-5042WND 

• Fuel Delivery

  • • Spradlin Bros. Welding, Columbus OH, Custom Stainless Steel Gas Tank w/ Straps

    • Classic Tube Stainless Steel Fuel Lines - Part#: JEF1014-SS

    • In-tank Pump

• Drivetrain

  • • Standard SBC Manual Bellhousing

    • LS7 Pilot Bearing to compensate for the LS1 crank offset - Part#: 12557583

    • 12" Clutch Kit, 10-spline, 1 1/8" input shaft, w/ throwout - Part#: LUK 04-064

    • Standard LS flywheel - Part#: Sachs NFW 1050

    • GM SM465 Manual 4-speed Transmission

    • GM NP205 Passenger Drop Married Transfer Case

    • JB Custom Fabrication Transfercase Shifters & Rails 

      • • Part#: SR205GM

        • Part#: BUGFM205GM

    • High Angle Driveline Transfercase Ebrake - Part#: 205EB

    • Custom 1 ton Drive Shafts

    • Custom Hillbilly Wizard CUCV Axles, WMS to WMS set at 77" 

      • • Dana 60 Front

        • Dana 70 Rear

        • 4.56 Gears

        • 4 Wheel Disk

        • Detroit Locker

        • Trail-Gear Creeper Breather - Differential Breather Kit - Part#: 140207-1-KIT 

• 24V -> 12V Conversion  

  • • Vintage Wiring of Maine stock reproduction body harness - Part#: VINT000873 

    • Swapped out early model analog turn signal box for late model solid state. 

      • • Military Vehicle 24V turn signal control - Part#: 11613632-3

        • Harness & Flasher - Part#: 11613631

        • Standard Warner 12v bulbs.  Will replace with LED soon.

        • NOTE: Box Swap Required for 12V turn signals.

    • Holly TerminatorX ECU & engine harness - Part#: HLY-550-929

    • Drive by Wire GM Gas Pedal

• Body

  • • Novak Engine Mounts - Part#: MMX-WG3

    • Custom BJ's Offroad Crawler Front Bumper 

      • • Part#: 25-1000-25-1001

        • Part#: 25-1001-FM

        • Part#: 25-1002-25-1004

    • Warn ZEON 12 Winch - Part#: 89120

    • Custom BJ's Offroad Rock Rails/Steps, Evil Twin Fab - Part#: 05-2663

    • Rugged Ridge Hood Catches - Part#: 11210.15

    • Raptor Lining Bed Liner Cab & Bed - Part#: UP0820

    • UPOL Gravitex Under Body Coating - Part#: UP0721

    • AU-VE-CO Products Door Weatherstrip - Part#: 16891

    • Robin Rielly Fiberglass Reproduction Gladiator Rino Grill

    • 1980s Grand Wagoneer Hood bar w/ additional hood pin.  Required at highway speeds to prevent hood cracking.

    • The Upholstery Man, Inc. Daytona FL, Modern Fabric Reproduction Convertible Top

• Interior

  • • New Vintage Gauges 1940 Series - Part#: 40614-03

    • ‎Mfm Building Product Peel & Seal Self Stick Roll Roofing, Aluminum foil rubberized asphalt waterproof sheeting - Part#: 50036

    • StockInteriors Carpet - Part#: 9296

    • FSJ Foot Well Vents w/ Aircraft Spruce Control Cables, Plain Dural Knob Control 8' - Part #: 05-14300 

    • The Upholstery Man, Inc. Daytona FL, Custom Rear Cab Wall Insulation Plate

    • Lane Dickey Upholstery, Longwood FL, 1977 Folding Jeep Truck Bench Seat

    • BJ's Offroad AC - Part#: 07-8072

    • Al Temple Reproduction Sill Plates

    • 1973-1987 GM SM465 Chrome Shifter for K30,K10 Square Body

• Steering

  • • Grant Steering Wheel & Adapter w/ 1960's Gladiator Horn Button (customized to fit)

      • • Part#: 4403

        • Part#: 410414

    • Borgeson Heavy Duty Telescopic Stainless Steel Steering Shaft

      • • Part#: 450024

        • Part#: 014940

        • Part#: 014952

        • NOTE: The stock column shaft will have to be ground to 3/4" DD

    • BJ's Offroad Read Head Steering Box

    • BJ's Offroad Read Head Pitman Arm

    • Skyjacker Dual Steering Stabilizers 

      • • Stabilizers - Part#: SJA-9220 

        • Rugged Ridge Stabilizer Bracket - Part#: 18040.50

        • TeraFlex Stabilizer Bracket - Part#: 1510000

• Wheels, Braking & Suspension

  • • Trailworthy Fabrication HMMWV 24 Bolt Wheels w/ Run Flat - Double Bead Lock Inserts - Part#: WHL-24BT1

    • Centromatic Front Axle Wheel Balancers - Part#: 400-408

    • Rancho RS9000XL Shock Absorbers

      • • Part#: RS999001

        • Part#: RS999338

    • BJ's Offroad Hydroboost - Part#: 3096-6773P

    • Adjustable Proportional Valve

• Other Stuff

  • • RockLaurence Custom 2" Trailer Hitch, need to request 44" frame width

    • EMP Shield Electrical System Pulse protection - Part#: DC-12V-W

    • Custom Magnaflow Dual Exhaust

    • Key Fob Battery Kill

• Contact Info

  • • BJ's Off-Road 

    • Trail Worthy Fab 

    • JB Custom Fabrication 

    • Hillbilly Wizard 

    • Centramatic 

    • Vintage Military Auto Wire Harness 

    • EMP & Lightning Protection 

    • Stock Interiors 

    • New Vintage USA 

    • Spradlin Bros. Welding Co. 

    • Novak Conversions 

    • Classic Tube 

    • U-Pol Raptor Liner 

    • Aircraft Spruce 

    • Restoration Specialist & Supply, Inc. 

    • Rock Laurence Vintage Auto Part 

    • Reproduction Gladiator Rino Grill, rrielly@verizon.net

    • Al Temple Sill Plates, Kaiserjeeps on M715zone.com

HUGE shout out to Dave Clark, crowtowncustomz@att.net and Dave Clark • Instagram   for making this happen!  Dave is a heck of a guy.  Highly skilled, talented, and trustworthy.   And his boss @ Jeff's Restoration in Holly Hill, FL for ALLOWING it to happen.  They both got into more than they bargained for but never complained a bit.  Beautiful work.

THANK YOU !!!